[MrCantelopeBMW]

any post on instructions and steps to install? and can you just code out the codes people are saying it's throwing?

[chrish_22]

Originally Posted by MrCantelopeBMW

any post on instructions and steps to install? and can you just code out the codes people are saying it's throwing?

Lots of youtube videos out there; fairly straightforward it seems. The "tricky" part is likely to be the portion where you would need a low profile torx socket to unscrew and remove the module from the headlight!

There shouldn't be any codes if done correctly. Make sure you are differentiating between US and Euro models.

[BobTheBimmer]

Just finished the install.

A tip for those trying to get that one screw out that is blocked and you don’t feel like drilling a hole.

There are 2 - 10mm bolts which you can remove and push the bracket to the side. This makes it possible to get your screwdriver in there to remove the screw.

[G20_Rick]

Originally Posted by Nembus

FYI for anyone doing this, I suggest mixing the thermal plaster they provide with a thermal paste for computer CPUs. Something like a 50\50 ratio or 75% plaster 25% thermal compound might be better to transfer that heat to the heat sink better to avoid the over heating of the board

I received the "version 2" from BayOptiks. This time around it came with thermal paste and metal backings on the modules. First set came with thermal tape and the modules did not have metal backings.

I was thinking of using thermal paste from computer CPUs. Any reason behind commending a 50/50 ratio?

[BLK.G20]

Originally Posted by chrish_22

Awesome! Actually just saw this earlier this morning. Gonna reach out and confirm fitment! Thank you!

Did you ever reach out to confirm fitment? Looks like no one has the boards for US spec cars. I've been talking with IceDriver on Aliexpress and I think I am going to send out a set of US spec LCI boards for him to work on, so hopefully he will have them available for US spec cars soon.

[chrish_22]

Originally Posted by ryann

Did you ever reach out to confirm fitment? Looks like no one has the boards for US spec cars. I've been talking with IceDriver on Aliexpress and I think I am going to send out a set of US spec LCI boards for him to work on, so hopefully he will have them available for US spec cars soon.

I did! They mentioned they were working on one, but have yet to have it released. I'll have to follow up with them to see! I did also reach out to IceDriver on Aliexpress and they asked to send my US boards to them and that they could get me a set. However, I am not in a position where I'd be able to do so.

If you end up doing it, let me know! Would love to see this happen and would appreciate that!

[prostcfc]

I got my yellow DRLs from Mod Emporium on Instagram. He probably gets it from the same source. It did require prying off the old ones from the heat sinks. Install is a PITA because to get to the outer monitors, you need to pull the headlights at least partially out to get access (or you can drill holes I guess), which requires removing the bumper. I also used the paste he shipped it with, and it seems to be holding fine after several months. Overall happy with the purchase and the effort was worth it IMO.

[Nembus]

Originally Posted by G20_Rick

I received the "version 2" from BayOptiks. This time around it came with thermal paste and metal backings on the modules. First set came with thermal tape and the modules did not have metal backings.

I was thinking of using thermal paste from computer CPUs. Any reason behind commending a 50/50 ratio?

Bit late with this but heard that with the supplied thermal adhesive it doesn't have the best thermal transfer efficacy. The idea behind having a 50/50 ratio is having the thermal adhesives cementing/sticking property and combining the thermal pastes better thermal thermal transfer properties.

[G20_Rick]

Had my "version 2" DRLs installed on Tuesday, September 12th. Used the method suggested by BobTheBimmer and it made things fast and easy for install. Also used the method suggested by Nembus with the 50/50 ratio of the thermal paste provided with the DRLs and CPU/GPU thermal paste. Took roughly 20-30 minutes for the 50/50 mix to dry/settle in the sun (cloudy SoCal day in the low 80's).

As for when we took the "version 1" DRLs out, we immediately noticed the DRL modules came right off the heat sinks. A further indication that the thermal tape was faulty by design. I didn't think of it at the time, but I should have taken photos of this. Also, the backings on the "version 2" DRLs have metal backings.

Will do a month update as the "version 1" DRLs didn't last that long. Hopefully you all don't hear from me before then.

[Nembus]

Originally Posted by G20_Rick

Had my "version 2" DRLs installed on Tuesday, September 12th. Used the method suggested by BobTheBimmer and it made things fast and easy for install. Also used the method suggested by Nembus with the 50/50 ratio of the thermal paste provided with the DRLs and CPU/GPU thermal paste. Took roughly 20-30 minutes for the 50/50 mix to dry/settle in the sun (cloudy SoCal day in the low 80's).

As for when we took the "version 1" DRLs out, we immediately noticed the DRL modules came right off the heat sinks. A further indication that the thermal tape was faulty by design. I didn't think of it at the time, but I should have taken photos of this. Also, the backings on the "version 2" DRLs have metal backings.

Will do a month update as the "version 1" DRLs didn't last that long. Hopefully you all don't hear from me before then.

Sweet, one thing I noticed when I took out my version 1 was the physical LED on the PCB board fell off. Pretty sure this board got super hot and fried something. Heat management seems to be key here so here's hoping we don't get issues. I've had my V2 boards on for almost two months now and haven't had a single issue. Fingers crossed

[soSick96]

Hey everyone, I am new to all this. I was searching for some modifications for my new car and stumbled upon this item: https://a.aliexpress.com/_mtkAziw
I am planning to buy RGBW DRL Module (EU-LED) and have few considerations before I buy it.
It looks dope but I am not sure if it will be a big problem to install it. I saw some videos on Youtube and honestly I don't feel very confident in removing front bumper for installation. The option which BobTheBimmer mentioned seems good and I might try it. The question I have is for those that ordered from IceDriver, did they provide thermal paster and how do I know if this item is version 2 and not version 1?

[MichaelNRW]

Originally Posted by soSick96

The question I have is for those that ordered from IceDriver, did they provide thermal paster and how do I know if this item is version 2 and not version 1?

I received a thermal glue and didn´t had any problems for the past 5 month.
Version 1 has a blank back while version 2 has a metal plate on the back.

[chutoy]

Originally Posted by soSick96

I don't feel very confident in removing front bumper for installation.

I installed IceDrivers on my 4 series and did not have to do a bumper pull. For the rear modules, check if you can access it from the wheel well behind the liner.
Also are some colors I.e. red and blue illegal in your country reserved for emergency vehicles?
DRL Install w/o bumper pull

[soSick96]

Damn it, I am not sure how it would look like on my standard led

[BLK.G20]

Originally Posted by chrish_22

Quick update for LCI owners, Euro Active Retrofit has informed me that they will be releasing US version for LCI G20 models in about 2-3 weeks! Will update once received!

Doesn't look like they have released anything yet. I sent a set of boards to BayOptiks in Cali for them to convert to yellow. Waiting to get them back.

[chrish_22]

Originally Posted by RMG8X

Doesn't look like they have released anything yet. I sent a set of boards to BayOptiks in Cali for them to convert to yellow. Waiting to get them back.

Awesome! Did you just buy extra boards? I was inclined to do that, but didn't want to be without them...

Funny enough, Bayoptiks is about an hour from where I live!

[mondayze]

Originally Posted by chrish_22

Quick update for LCI owners, Euro Active Retrofit has informed me that they will be releasing US version for LCI G20 models in about 2-3 weeks! Will update once received!

still not released?

[BLK.G20]

Originally Posted by chrish_22

Awesome! Did you just buy extra boards? I was inclined to do that, but didn't want to be without them...

Funny enough, Bayoptiks is about an hour from where I live!

Yeah I just got a second set. They were only $200 for the pair. That way I could have a backup set if I ever need them for some reason. The boards should be delivered to them today. They told me it will take 2-3 weeks for them to convert them.

[chrish_22]

Originally Posted by mondayze

still not released?

Yeah..unfortunately no response...

[chrish_22]

Originally Posted by RMG8X

Yeah I just got a second set. They were only $200 for the pair. That way I could have a backup set if I ever need them for some reason. The boards should be delivered to them today. They told me it will take 2-3 weeks for them to convert them.

Where did you get that second set?

Also, do you mind me asking how much bayoptiks is charging?

[vader_330]

Originally Posted by Daily_Dravit

I’ve seen all the G8x and G22 yellow DRL conversions. Haven’t been able to find anyone who did the yellow DRL conversion on a G20. Just trying to confirm there is no issue. If nobody has done it, I’ll be a Guinea pig and report back

I have seen the yellow DRLs available on: https://modeautoconcepts.com/product...1ff58ea5&_ss=r
Thinking of getting this for my 330i

[BLK.G20]

Originally Posted by chrish_22

Where did you get that second set?

Also, do you mind me asking how much bayoptiks is charging?

Got it from my dealer, the set retails for like $350 something but the employee pricing brought it down to $200. BayOptiks is charging $150.