09-11-2021, 12:29 PM | #177 | |
Colonel
1161
Rep 2,180
Posts |
Quote:
This is simple - tell your seller (not anybody in this thread) to exchange the UP-7DSP with the UP-7BMW with the bracket. That's it. |
|
Appreciate
0
|
09-11-2021, 03:51 PM | #178 | |||
//\\
3
Rep 21
Posts |
Quote:
Quote:
Quote:
Unfortunately my seller is in Austria so it will cost $$$ to swap amps. |
|||
Appreciate
0
|
09-11-2021, 04:36 PM | #179 | |
Second Lieutenant
78
Rep 222
Posts |
Quote:
Or take it to an installer? Last edited by AustraliaG20; 09-11-2021 at 04:46 PM.. |
|
Appreciate
0
|
09-11-2021, 04:54 PM | #180 | |
Colonel
1161
Rep 2,180
Posts |
All it is needed is to run a cable from the battery, that’s as good as PnP with the RAM harness.
Quote:
|
|
Appreciate
0
|
09-12-2021, 09:09 AM | #181 |
New Member
0
Rep 8
Posts |
I had UP 7DSP/MEC-Analog installed in my 2021 G21 with PP-BMW 1.7RAM cable, this is confirmed by Audiotec Fischer that what I need to have. It's a little inconvenient because I need to hardwire the power cable to the car battery, if UP 7BMW can run without power cable, why Audiotec Fischer wants us to use 7DSP?
|
Appreciate
0
|
09-12-2021, 10:26 AM | #182 | |
Colonel
1161
Rep 2,180
Posts |
Quote:
|
|
Appreciate
0
|
09-13-2021, 01:24 PM | #183 |
//\\
3
Rep 21
Posts |
Trying to install the MEC-Analog -
Should the input sensitivity be set to 11v/3.5v or 30v/8v? Should the jumper be on or off? Should the highlevel input auto remote turn-on function be set to on or off? |
Appreciate
0
|
09-13-2021, 02:00 PM | #184 |
Colonel
1161
Rep 2,180
Posts |
|
Appreciate
0
|
09-15-2021, 04:17 PM | #185 |
//\\
3
Rep 21
Posts |
The Saga Continues...
4 gauge wire kit I bought power wire was way too big after stripping to fit the 7DSP's power molex connector. Returning it for an 8 gauge kit. In terms of the battery should I be running the 12v cable to the terminal on the battery itself? Or to the little red box that sits next to the battery? Still not sure how I'm going to secure the amp to the car...don't think I have anything that can drill through the metal. Wonder if I can just buy the mounting bracket and screw plugs separate from bimmertech... |
Appreciate
0
|
09-18-2021, 11:07 PM | #187 |
//\\
3
Rep 21
Posts |
|
Appreciate
0
|
09-19-2021, 02:55 AM | #188 |
Second Lieutenant
78
Rep 222
Posts |
I don't think it really matters, it's more about what is easier to access as both are close enough to the battery. But yes, my installer (AF certified) used the junction box.
|
Appreciate
0
|
09-20-2021, 05:32 AM | #189 |
First Lieutenant
209
Rep 310
Posts |
|
Appreciate
0
|
09-20-2021, 04:21 PM | #190 |
//\\
3
Rep 21
Posts |
Alright, after a herculean effort under the beating sun in this sweltering heat I installed everything properly (i hope) nice and snug (i hope) and put everything back together fitting properly with no bulges or anything looking amiss.
Dealing with the DSP pc tool now... Last edited by MashMaster; 09-20-2021 at 04:47 PM.. |
Appreciate
0
|
09-20-2021, 09:02 PM | #192 |
//\\
3
Rep 21
Posts |
Here is what mine looks like:
Is that right? Also on the main tab AMP Out A has a red square as does Front L Full. Is that bad? Also should I have Sub Xpander, Clarity Xpander, or Stage Xpander enabled? For sub xpander what should the Dynamic Boost settings be? Last edited by MashMaster; 09-20-2021 at 09:14 PM.. |
Appreciate
0
|
09-20-2021, 11:57 PM | #193 |
Second Lieutenant
78
Rep 222
Posts |
I got mine done by the tuner, but can you start with one of the setups from here?
https://www.audiotec-fischer.de/en/m...ase/soundIndex |
Appreciate
0
|
09-22-2021, 02:05 AM | #194 |
Private
14
Rep 74
Posts |
pneumodoc
How did you physically mount the Match amp? I've watched a couple install videos (the Bimmertech one is the best) but they include a specific mounting bracket to relocate the existing RAM unit, leaving the original mounting position for the Match amp. I don't have that bracket. My first thought was to just velcro it down but I'm wondering if there is a more sophisticated method. |
Appreciate
0
|
09-22-2021, 10:18 AM | #195 |
New Member
0
Rep 8
Posts |
|
Appreciate
0
|
09-22-2021, 08:01 PM | #196 | |
Lieutenant
232
Rep 422
Posts |
Quote:
|
|
Appreciate
0
|
10-31-2021, 11:32 AM | #198 |
Colonel
1161
Rep 2,180
Posts |
The 6-speaker system may be not wired for the harness of this AF amp, depending on having a RAM-system or an OEM HU-system with 6 speakers.
Last edited by Encanto; 10-31-2021 at 11:40 AM.. |
Appreciate
0
|
Post Reply |
Bookmarks |
Thread Tools | Search this Thread |
|
|