02-25-2020, 11:52 AM | #133 | |
Captain
345
Rep 751
Posts |
Quote:
Last edited by siegester; 02-25-2020 at 07:22 PM.. |
|
Appreciate
0
|
02-28-2020, 01:56 PM | #134 | |
Major
658
Rep 1,479
Posts
Drives: 2020 M340Xi (G20)
Join Date: Sep 2013
Location: Virginia
|
Quote:
Just coded what you had in first post. How do you access the Seat Heating Distribution -- in other words, how do I get to it on iDrive? Thanks
__________________
Al
2020 M340Xi| ZDA| ZDY| ZPP| ZPX| 1CR| 1PL| 688| 6NW| 2VFH| Retired: 2014 328i BMW CCA |
|
Appreciate
0
|
02-28-2020, 02:49 PM | #135 |
Major
658
Rep 1,479
Posts
Drives: 2020 M340Xi (G20)
Join Date: Sep 2013
Location: Virginia
|
Owner's Manual in Motion
Hi,
When I coded Video in Motion, it worked for videos, BUT it didn't seem to work for the on-board owner's Manual. I did some digging in the HG_MGU module of my M340 and found the following functions which I changed from Aktiv to NichtAktiv to allow use of the on-board owner's manual:
While the last function is not part of the manual, I found it useful to also make it available while in motion
__________________
Al
2020 M340Xi| ZDA| ZDY| ZPP| ZPX| 1CR| 1PL| 688| 6NW| 2VFH| Retired: 2014 328i BMW CCA |
Appreciate
0
|
02-28-2020, 08:11 PM | #136 |
Captain
345
Rep 751
Posts |
These menus change a bit based on what is enabled, but it should be either in the same place as the auto seat heater configuration, or in a stand alone seat heating menu under the climate control menu (I believe there is even a third menu configuration, but I cannot recall what it was).
|
Appreciate
0
|
02-29-2020, 01:07 PM | #137 | |
Major
658
Rep 1,479
Posts
Drives: 2020 M340Xi (G20)
Join Date: Sep 2013
Location: Virginia
|
Quote:
Hmm, I just checked and can't find that menu in either place or anywhere. I coded the two BDC & one SM2 functions in your original post, but I suspect some function has to be coded in the HG_MGU ECU -- perhaps:
__________________
Al
2020 M340Xi| ZDA| ZDY| ZPP| ZPX| 1CR| 1PL| 688| 6NW| 2VFH| Retired: 2014 328i BMW CCA |
|
Appreciate
0
|
03-01-2020, 10:49 AM | #138 |
New Member
3
Rep 27
Posts |
Got a few questions. Has anyone heard from tokenmaster? I have been waiting since December with no response. Also is any of this coding possible with just Esys alone and not the launcher? Trying to get lane change assist and the auto heated steering wheel working on a g20. Everything else I’ve done with Bimmercode. Thanks in advance for any info.
|
Appreciate
0
|
03-01-2020, 03:37 PM | #139 | ||
Captain
345
Rep 751
Posts |
Quote:
Quote:
You cannot really code without esysx or launcher pro as they provide the mappings which make the trimmed values make sense to a human Last edited by siegester; 03-01-2020 at 03:45 PM.. |
||
Appreciate
1
RSnic657.50 |
03-01-2020, 05:20 PM | #140 |
New Member
3
Rep 27
Posts |
Thanks siegester. I figured as much in the esys. I'm pretty sure I did every thing correct for tokenmaster. I paid him directly. He had no problem taking my money! I've been looking to see anyone acknowledge talking to him or getting the latest launcher but I haven't come across anything past December.
|
Appreciate
0
|
03-03-2020, 01:13 PM | #141 | |
Major
658
Rep 1,479
Posts
Drives: 2020 M340Xi (G20)
Join Date: Sep 2013
Location: Virginia
|
Quote:
That did the trick! The driver slide seems to work fine, bu I see what you mean about front passenger -- can't get it to save slide setting; oh well! THANKS!!!
__________________
Al
2020 M340Xi| ZDA| ZDY| ZPP| ZPX| 1CR| 1PL| 688| 6NW| 2VFH| Retired: 2014 328i BMW CCA |
|
Appreciate
0
|
03-05-2020, 09:15 AM | #142 |
Private
25
Rep 63
Posts |
Hi guys i coded lane change, temp when stearing wheel starts, but one thing i can't find and its when trying to code heat distribution i can't find "SM2 -> SHZ_TYP -> werte 02"......Where is this "SM2"??
|
Appreciate
0
|
03-05-2020, 10:36 AM | #143 | |
Major
658
Rep 1,479
Posts
Drives: 2020 M340Xi (G20)
Join Date: Sep 2013
Location: Virginia
|
Quote:
SM2 is the ECU that handles seat items; on my M340. its CAFD is 2259. FYI, when using E-Sys (and I think also for Bimmercode), the ECUs are listed alphabetically on the SVT (again in E-Sys) Hope that helps!
__________________
Al
2020 M340Xi| ZDA| ZDY| ZPP| ZPX| 1CR| 1PL| 688| 6NW| 2VFH| Retired: 2014 328i BMW CCA |
|
Appreciate
0
|
03-28-2020, 06:46 AM | #145 |
Enlisted Member
10
Rep 47
Posts |
when changing to werte 2, however, a separate ntc sensor for backrest and seat must be installed in the seat. this is only the case with climate-controlled seats, isn't it?
|
Appreciate
0
|
04-07-2020, 12:29 AM | #146 |
Petrolhead
1948
Rep 3,521
Posts |
It probably is since people have coded it in but it doesn’t work on the G20.
__________________
Current:
2020 BMW 330i xDrive 2018 Audi SQ5 Prestige 2017 Audi A7 Prestige |
Appreciate
0
|
04-07-2020, 11:01 PM | #147 |
Captain
345
Rep 751
Posts |
Which file are you looking for? Esys, Launcher Pro, cheat codes? The cheat codes are in a format that launcher pro understands and brings into esys. You just download the code file, and put it in the esys directory (see first post for exact location)
|
Appreciate
0
|
04-08-2020, 04:41 AM | #148 |
Second Lieutenant
45
Rep 243
Posts |
Hi guys, new to coding and have a couple of quick questions please:
1) I've seen a few cheap Enet adapters on eBay that say they are for the F-series. Presumably they would work on a G-series too wouldn't they? The pinouts for the ODB2 port are the same for both series I'd have thought? 2) I'm slightly confused whether I need Launcher for G-series? From the 1st post links I've downloaded Esys 3.27.1, PSdZData Lite 4.21.32 and the Launcher Pro that Tokenmaster was giving away in his blog, 2.8.2 build 162. But the Launcher token is only valid till 20th of this month and I haven't got my enet cable yet. But I'm only wanting to code one or two things so I don't really want to pay the £50 to get the token for a newer version especially as some people seem to have difficulty with him responding. 3) Between 1) and 2) above will I have everything I need? (Obviously I have a laptop.) Thanks. |
Appreciate
0
|
04-08-2020, 11:30 AM | #149 | |
Major
658
Rep 1,479
Posts
Drives: 2020 M340Xi (G20)
Join Date: Sep 2013
Location: Virginia
|
Quote:
Let me give your questions a go. I have an ENet cable that I used on my F30 and have also used now on my G20. On your laptop, you need the items listed. If you want to get the long term token, there are instructions in another thread on this forum or go to BimmerFest coding forum and get them there. From what I gather from posts, you must follow instructions EXACTLY and TokenMaster is notalways quick to respond. Hope that helps!
__________________
Al
2020 M340Xi| ZDA| ZDY| ZPP| ZPX| 1CR| 1PL| 688| 6NW| 2VFH| Retired: 2014 328i BMW CCA |
|
Appreciate
0
|
04-08-2020, 02:29 PM | #150 |
Second Lieutenant
45
Rep 243
Posts |
Thanks for your reply. So that answers the question about the Enet adapter.
I have all the software on my laptop ready to go. Will all the versions I listed work and be suitable for the G20? And can the coding be done without using Launcher, ie just Esys? It seems that the main software is free but then you have to pay £50 just to add the cheat codes in with Launcher. It's a lot for what I want. |
Appreciate
0
|
04-08-2020, 07:44 PM | #151 | ||
Major
658
Rep 1,479
Posts
Drives: 2020 M340Xi (G20)
Join Date: Sep 2013
Location: Virginia
|
Quote:
Quote:
Because the data is clipped, you have to use the Launcher which basically. maps function names & the like back with the data. Cheat codes, though used within Launcher, are free & not part of Launcher (I use Almaretto's -- see thread Getting started with E-Sys for how to get). I am not sure what is most current PsdZData set. if the data set is the same or newer then the software version, you are OK. Again, you must use Launcher Hope that helps
__________________
Al
2020 M340Xi| ZDA| ZDY| ZPP| ZPX| 1CR| 1PL| 688| 6NW| 2VFH| Retired: 2014 328i BMW CCA |
||
Appreciate
0
|
04-09-2020, 04:59 AM | #152 |
Second Lieutenant
45
Rep 243
Posts |
OK thanks for clarifying. I'll just have to fork out the £50 and hope that Tokenmaster responds promptly. Or if I get my cable in time I'll try the free version. I only really want to code one thing (Enhanced Bluetooth) for now at least. Wished I'd added it when ordering but didn't realise what it was.
|
Appreciate
0
|
04-09-2020, 11:00 AM | #153 | |
Major
658
Rep 1,479
Posts
Drives: 2020 M340Xi (G20)
Join Date: Sep 2013
Location: Virginia
|
Quote:
Please be sure to read the instructions earlier in this thread as several didn't and had problems Good luck and welcome to coding!
__________________
Al
2020 M340Xi| ZDA| ZDY| ZPP| ZPX| 1CR| 1PL| 688| 6NW| 2VFH| Retired: 2014 328i BMW CCA |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|